Gas fireplace pilot wont stay lit. gas fireplace won't start

Gas Fireplace won't stay lit

gas fireplace pilot wont stay lit

The way milivolt gas fireplaces work is that the pilot light generates electricity under 1 volt and sends it the wall switch. After reading these posts, I had seen a little box under the fireplace so I pulled that out, it's a remote start which seems to work fine. The thermocouple is the copper rod the pilot flame directly hits. Tried turning the gas on to the logs and lighting it with a match and nothing, almost as if the logs are not getting any gas. You awake on a cold winter morning and cast the covers aside. When it does cut itself off the pilot light goes out again.

Next

5 Reasons Why Your Pilot Light Keeps Going Out

gas fireplace pilot wont stay lit

Change the batteries, and it came back to life. In these systems, the pilot will only light in the case of hot surface igniters, the igniter surface heats when the thermostat makes a command for heat. The connector on the new switch did not match the old one so I had to splice the wire from the fireplace to the new receiver together. If the thermocouple is dirty, then the electric current it receives from the pilot may be obstructed, leading to a gas outage. Typically, the flame should lightly touch the thermocouple or be close enough to heat the device. These tiny holes can become dirty or clogged from carbon very easily. Just sharing what worked for me.

Next

How to troubleshoot gas fireplace that won't light

gas fireplace pilot wont stay lit

Again, manual operations work fine. Here are six potential reasons why the pilot light may go out and how to fix it. More often than not the hearth will perform poorly, not fail to stay lit. If gas is coming out of the pilot, but it still won't light, the spark igniter could be the problem. I purchased a vent free gas fireplace this past spring when they were one sale at a local store and it seemed to work fine with the little testing I did to make sure it worked properly. One thing you can try if the gas fireplace shuts off after a few minutes: there's a small screw on your valve that regulates the size of your pilot flame.

Next

6 Reasons Why a Water Heater Pilot Light Won't Stay Lit

gas fireplace pilot wont stay lit

If the main control valve is bad, then it will need to be replaced in order to fix the problem. While it was pulled out, I started it and it ran fine until I turned it off to put everything back together. In my area they provide a free service to connect gas appliances and inspect them. Another common culprit is incorrect gas pressure. Naturally, an unreliable pilot light is something that you should worry about and fix as soon as you notice it. This opens the gas valve and allows gas to enter the burner ports…and voila, fire! Hold it down for at least 30 seconds in order for the thermocouple to get warmed up.

Next

6 Reasons Why a Water Heater Pilot Light Won't Stay Lit

gas fireplace pilot wont stay lit

Because this is a real flame, will not effect like that of. It should be nearby or even on your furnace. Any help would be appreciated. We put in a new thermo pile and light switch, but it still won't light up the whole bar. But I am guessing and dont know if what I recomend is safe. You'll have to remove the cover, and chances are the lighting won't be working in your favor. For safety's sake, shut off power to the furnace by switching the breaker to the off position, and close the gas valve.

Next

What to Do if a Gas Furnace Pilot Light Won't Stay Lit

gas fireplace pilot wont stay lit

The pilot light was still lit, but the main burner was off. Observe if the fireplace comes on. If the gas logs light you have found your problem! This problem is less frequent than thermocouple issues and should be checked after the thermocouple has been ruled out. Hire a gas fireplace expert if you have any doubts. It can easily be cleaned off with fine grain sandpaper.

Next

DIY: Gas Fireplace Won't Light? How to Clean your Thermopile and Thermocouple

gas fireplace pilot wont stay lit

This is probably the easiest thing to test and replace. When starting your troubleshooting process check if the pilot lighting is functioning properly. Where can I buy another one or have it checked out? It is recommended to replace the whole pilot head instead of just the thermocouple. The numbers are much better now but still the main burner won't trip on when I flipped the switch. It's controlled by a wall switch. Ventless Real-Fyre G9-2 unit with wall mounted remote. Any ideas on how to fix it myself I have already found that the wall switch has juice, and there's obviously gas to the burner unit or any recommendations of somewhere I can take the unit for repair in the West Los Angeles area? I recommend using a soft bristle brush, rags and a toothbrush to get the job done.

Next