Washer spin cycle not working. Here’s Why Your Washing Machine’s Spin Cycle is Not Working

How to Fix Washer That Won't Spin

washer spin cycle not working

In a top-loading washer, a small protrusion on the underside of the lid depresses a switch when you close the lid, serving as a safety precaution to detect when the lid is closed. With the door of the washing machine open, try turning the drum. If the protrusion has bent out of shape, it may not trigger the switch as intended. As a result the clothes will feel wet and the inside of the unit will have more water than usual. It may be loose, worn, or broken. Use this information at your own risk.

Next

Solved: Washer stuck in spin cycle WF45K6500A

washer spin cycle not working

You will need to remove all or part of the cabinet to access it, it will likely be found near the door lock mechanism. Best Answer I think it depends on the cost of repair services in your community. It started to spin but then stopped, I fear the new coupler is broken but don't have time to investigate until tomorrow night. You may freely link to this site, and use it for non-commercial use subject to our. Sometimes, your washer can simply be old, worn out, and in need of a replacement. Tighten the belt or replace it entirely.

Next

SOLVED: Washer drains spin cycle, but won't spin.

washer spin cycle not working

Not sure if that's part of the malfunction or if it keeps adding time as it thinks it's either going or not going through the cycle and realizes it needs more time? Note: The amount of water will vary according to when in the cycle the issue occurred. If not, you may need to replace the drive belt. If possible, a may be enough to get the job done. He quickly took the oven apart, which indicated to me that he knew what he was doing. Fixing problems with your washing machine require a certain amount of knowledge in order to do things correctly. It will take you 10min and you only need a wrench and screw driver.

Next

Here’s Why Your Washing Machine’s Spin Cycle is Not Working

washer spin cycle not working

I can't say that this will fix everyone's issues but it seemed like the logical starting point and worked for me. Again, this is a small and simple job. Drive Motor If the washer won't spin or agitate the drive motor might be defective. To troubleshoot this on your washing machine, you first you'll need to take off the access panel make sure that the washing machine is unplugged first and see if the pump can turn freely when loosening tension from the belt. Don pinnell I have the same issue.

Next

Reasons Why Your Washing Machine Won't Spin

washer spin cycle not working

Motor Coupler Some manufacturers use a small motor coupling made of rubber and plastic. The unit will try to get rid of some of the excess of suds by adding time to the cycle, up to 2 hrs. But no matter what type of laundry you're washing, the spin cycle is one of the machine's most important. This part is often misdiagnosed. Test any switches on the door lock with an Ohm meter.

Next

Spin Cycle Not Working on Washer

washer spin cycle not working

If the tub is not spinning, you may have a damaged motor coupler. Plug it back in and then see if the spin cycle will restart. Verify that the switch is being activated mechanically and that any levers or actuators are not damaged or sticking. Reset the breaker see if the washer starts to spin. If you notice excessive wetness, check that the load is properly balanced and redistribute the items if necessary before restarting the spin cycle. You should receive a reading of 1500 to 1900 ohms.

Next

Maytag washer spin cycle not working properly

washer spin cycle not working

Is you Kenmore or Whirlpool Washer Not Spinning or does it make a loud noise when you turn it on? Plus, relying on an extension cord will shorten the useful life of the washer. Even with the washer unplugged, induction-type motors that contain capacitors can give you quite an electric shock, so motor testing and repairs are best left to the pros. Oh, and since it's a top loader, don't forget to check if it's affected by the recall. A broken drive belt, or one that has slipped off the pulley wheel, can cause the washer to agitate during the wash cycle and yet—despite the noise of the motor running—the drum remain still during the spin cycle. If the clothes are too wet at the end of the cycle, this could be the result of a drain restriction or an unbalanced load. The door lock can fail either mechanically or electrically. Kenmore makes washing machine in a variety of models, including top- and front-loaders and high-efficiency units that save on energy costs and water consumption.

Next

Washer Doesn't Agitate or Spin

washer spin cycle not working

The dealership was really interested in selling me the newer car. . This will perform a spin only cycle. I tried to turn the wash tub and it is stuck; so I can't manually spin it. Be sure that the advice you get from a repair person is valid. If the machine starts spinning normally, simply re-bend the protrusion so it triggers the spin switch properly. From here, you can see when or where the problem occurs: before the spin cycle or during.

Next